Lanbao PU05M | U-Shaped Sensor | 5mm

Lanbao PU05M – U-shaped photoelectric sensor

The Lanbao PU05M is a U-shaped photoelectric sensor built for through-beam slot sensing in industrial automation equipment. Lanbao’s official specification lists 5mm, NPN; PNP (based on current SKU options), 5…24 VDC (Ripple p-p: 10%) supply, and See selected SKU. This OpenELAB listing summarizes the product family for selectable SKUs, so always match the required output and connection against the variant name before ordering.

For selection, confirm the sensing principle, range, output type, connection style, response time, protection rating, and accessory set against the exact SKU. Use the SKU code on the order page as the final reference for output polarity and cable style. If you are comparing nearby Lanbao models, also review Lanbao PU05M 1002, Lanbao PSE-PM2, and Lanbao PSE-PM8 so the housing style, measurement method, and control output match the machine input.

Technical Specifications

Parameter	Value
Model family	PU05M
Sensor type	U-shaped photoelectric sensor
Detection / measuring range	5mm
Sensing method	Through beam
Output configuration	NPN; PNP (based on current SKU options)
Supply voltage	5…24 VDC (Ripple p-p: 10%)
Response time	1KHZ (The maximum value is 3KHZ)
Light source	Infrared LED (940nm)
Load / output current	50mA
Connection	See selected SKU
Protection rating	IP65
Material	PBT
Operating temperature	-25…55(Optical surface no icing,nocondensation)
Indicator	Yellow: output indication

Board Layout & Label Guide

• Slot opening – Keep the active face clean and align it to the target path required by through-beam slot sensing.
• Output indicator – Use the LED indication to confirm power, switching state, and any short-circuit or overload warning described by the official specification.
• Connection area – See selected SKU; route the cable or connector with strain relief before final commissioning.
• Supply input – Wire the sensor only within 5…24 VDC (Ripple p-p: 10%); confirm polarity before applying power.
• Output selection – Match the selected SKU to this listing’s output coverage: NPN; PNP (based on current SKU options).
• Adjustment / teach control – Use the controls described for the selected SKU; set the distance or threshold after the sensor is mounted in its final position.
• Mounting body – Use the listed accessory hardware and avoid mechanical stress on the lens, slot, or transducer surface.
• Protection rating – IP65; maintain sealing around the cable entry or connector during installation.

Packing List

• 1 x Lanbao PU05M sensor for the selected SKU
• Mounting hardware or accessories as supplied with the selected warehouse batch
• Product documentation and official specification reference
• Current store bundle contents may vary by SKU and warehouse batch

FAQ

Q: What is the main function of the Lanbao PU05M?
A: It is a U-shaped photoelectric sensor for through-beam slot sensing, with the range and output behavior defined by the selected SKU.

Q: Which power supply should I use?
A: Use 5…24 VDC (Ripple p-p: 10%) and confirm the sensor wiring before applying power.

Q: Which output type should I order?
A: Choose the SKU that matches the controller input. Current output coverage for this listing is: NPN; PNP (based on current SKU options).

Q: Does the sensing distance always equal the rated value?
A: Use 5mm as the official reference, then validate with the real target, mounting angle, and surface condition.

Q: What should I check before commissioning?
A: Check supply voltage, output wiring, target alignment, LED status, mounting stability, and the selected distance or teach setting.

Q: Can I use it in wet or dusty equipment?
A: The official protection rating is IP65. Keep the connector, cable outlet, and sensing face sealed as installed.

Q: Is the product sold as all variants together?
A: No. Select the required SKU from the store options; the title and description summarize the compatible product family.

Q: Where should I verify final parameters?
A: Use the official Lanbao specification page and the SKU shown on your OpenELAB order.