Lanbao UR18-DC60 | Ultrasonic Sensor | 30-60mm

Lanbao UR18-DC60 – ultrasonic distance sensor

The Lanbao UR18-DC60 is a ultrasonic distance sensor built for ultrasonic sensing in industrial automation equipment. Lanbao’s official specification lists 30-60mm, NPN NO; NPN NC; PNP NO; PNP NC (based on current SKU options), 18…30VDC supply, and 2m PVC cable. This OpenELAB listing summarizes the product family for selectable SKUs, so always match the required output and connection against the variant name before ordering.

For selection, confirm the sensing principle, range, output type, connection style, response time, protection rating, and accessory set against the exact SKU. Use the SKU code on the order page as the final reference for output polarity and cable style. If you are comparing nearby Lanbao models, also review Lanbao UR12-DC40, Lanbao PDE-CR30, and Lanbao PDE-CR50 so the housing style, measurement method, and control output match the machine input.

Technical Specifications

Parameter	Value
Model family	UR18-DC60
Sensor type	ultrasonic distance sensor
Detection / measuring range	30-60mm
Sensing method	ultrasonic sensing
Output configuration	NPN NO; NPN NC; PNP NO; PNP NC (based on current SKU options)
Supply voltage	18…30VDC
Response time	See official specification
Load / output current	See official specification
Connection	2m PVC cable
Protection rating	IP67
Material	Copper nickel plating, glass bead filled epoxy resin
Operating temperature	-25 …70 (248-343K)
Indicator	Green LED: single sheet detected ; Yellow LED: no target (air) ; Red LED: double sheets detected

Board Layout & Label Guide

• Ultrasonic transducer face – Keep the active face clean and align it to the target path required by ultrasonic sensing.
• Output indicator – Use the LED indication to confirm power, switching state, and any short-circuit or overload warning described by the official specification.
• Connection area – 2m PVC cable; route the cable or connector with strain relief before final commissioning.
• Supply input – Wire the sensor only within 18…30VDC; confirm polarity before applying power.
• Output selection – Match the selected SKU to this listing’s output coverage: NPN NO; NPN NC; PNP NO; PNP NC (based on current SKU options).
• Adjustment / teach control – With teach-in function; set the distance or threshold after the sensor is mounted in its final position.
• Mounting body – Use the listed accessory hardware and avoid mechanical stress on the lens, slot, or transducer surface.
• Protection rating – IP67; maintain sealing around the cable entry or connector during installation.

Packing List

• 1 x Lanbao UR18-DC60 sensor for the selected SKU
• Mounting hardware or accessories as supplied with the selected warehouse batch
• Product documentation and official specification reference
• Current store bundle contents may vary by SKU and warehouse batch

FAQ

Q: What is the main function of the Lanbao UR18-DC60?
A: It is a ultrasonic distance sensor for ultrasonic sensing, with the range and output behavior defined by the selected SKU.

Q: Which power supply should I use?
A: Use 18…30VDC and confirm the sensor wiring before applying power.

Q: Which output type should I order?
A: Choose the SKU that matches the controller input. Current output coverage for this listing is: NPN NO; NPN NC; PNP NO; PNP NC (based on current SKU options).

Q: Does the sensing distance always equal the rated value?
A: Use 30-60mm as the official reference, then validate with the real target, mounting angle, and surface condition.

Q: What should I check before commissioning?
A: Check supply voltage, output wiring, target alignment, LED status, mounting stability, and the selected distance or teach setting.

Q: Can I use it in wet or dusty equipment?
A: The official protection rating is IP67. Keep the connector, cable outlet, and sensing face sealed as installed.

Q: Is the product sold as all variants together?
A: No. Select the required SKU from the store options; the title and description summarize the compatible product family.

Q: Where should I verify final parameters?
A: Use the official Lanbao specification page and the SKU shown on your OpenELAB order.